Weiser Technik’s Extreme EVO LED Motorcycle Light Kits transformed my 2020 BMW R 1250 GS test mule into a much more conspicuous presence on the road by adding running light capability to the front turnsignals and running light with brake light capability to the rear turnsignals. The kits essentially replace the stock turnsignal modules with Weiser’s own design, which utilizes 12 super-bright Osram LEDs per indicator. The result is dramatic, especially at night where the GS’s relatively meager stock lighting was once easily lost in the sea of traffic.

In addition to the 4 LED light modules, the Weiser LED motorcycle light kits arrived complete with all necessary components for installation – including standard wiring, extension wiring, zip ties, posi-twists, posi-taps, posi-locks, locking keys, and solid-state relay – and full instructions. Many variations of the kits are available to fit a myriad of brands and models, and generally the LED light modules fit within OEM housings. However, Weiser also offers the turnsignal housings themselves (if necessary), clear or tinted lenses, and short (4.2 inch), medium (4.6 inch), or long (6.25 inch) turnsignal stems to fit nearly any application.

The lights are fully CANbus-compatible, so no load equalizers are necessary, and there is no danger of fault codes if installed properly.  Installation itself is relatively straightforward for the shade-tree mechanic using online tutorials and the printed manual that came with the kit, but since my bike was in for service already, I had my shop install everything in one hour of labor. 

Pre-Weiser, my GS’s turnsignals were devoted solely to that function and otherwise remained unlit. With the Weiser kits installed, the front turnsignals now glow a constant bright white color as full-time running lights. Activating the turn signal overrides the white running light with a bright flashing yellow-off-yellow pattern and then glows continuously white again once the turnsignaling is canceled.

The rear setup operates in a similar fashion to the front, with both indicators operating as full-time red running lights. If the rider hits the brakes, both indicators glow an intense bright red. If the turnsignals are utilized, the side indicating glows in a yellow-red-yellow-red sequence until the turnsignal is canceled and then resumes its red running light mode. Hazard lights operate as normal, flashing yellow-off-yellow up front and yellow-red-yellow in the rear.  

Out on the road, the Weisers drew plenty of compliments from my fellow riders, especially at night when the additional lighting really popped compared to the stock dim setup. The company claims their lights are up to 10 times brighter than OEM, an entirely believable claim based on my observations. The kits I tested carry a four-year warranty with tech support available by phone or online.

See all of Rider‘s Parts & Accessories reviews here.

The Weiser Extreme EVO LED motorcycle light kits tested here are $249-$269 for both the dual-function front kit and triple-function rear kit or $449-$489 for a combo kit. 

The post Weiser Extreme EVO Multifunction LED Motorcycle Light Kits | Gear Review appeared first on Rider Magazine.

After nearly two decades aboard various generations of BMW’s venerable RT-Series sport-tourers, I recently decided to learn how to ride off-road and made the switch to a BMW R 1250 GS adventure-tourer The GS is surely a capable machine, but it’s not quite the glass-smooth operator my RT was on the highway. Though by no means offensive, the GS’s handlebar transmits a modicum of vibrations to the rider’s hands as the revs climb, and Hudson Valley Motor Parts Motorcycle Bar End Weights represent a compelling antidote to this. By adding copious mass to the bar ends, these weights effectively quell the sympathetic resonance which plagues all motorized two-wheelers to some degree.

Related: 2021 BMW R 1250 GS | Road Test Review

My HVMP test pair was perfectly finished in gloss black, with each bar end weighing a portly 8.9 ounces sans hardware and measuring 1.6 inches high by 1.5 inches in diameter at the base. For reference, the GS’s stock bar end weighs a scant 2.2 ounces sans hardware and measures 1 inch high by 1.5 inches in diameter at the base.

Installation was a breeze and required only common hand tools. The GS’s stock bar ends must be removed by loosening the T45 Torx bolts which hold them in place. Then, they are replaced with the HVMP units, which are fastened via the included 6mm stainless Allen bolts. It’s a good idea to add some medium strength thread locking compound (Loctite or Permatex blue) to the bolt threads. Torque to 9 lb-ft, and you’re done. There is no interference whatsoever with the GS’s handguards, and the whole process takes less than 10 minutes for the pair.

See all of Rider’s Parts & Accessories reviews here.

On the road, the HVMP motorcycle bar end weights had a dramatic effect on handlebar vibes throughout the entire rev range. The GS’s handlebar is now dead still below 4,000 rpm, and the buzz which used to emanate from the grips above 4,000 rpm is now reduced by what feels like 75%, making spirited riding and downshifting much more enjoyable. My GS’s grips are smoother now than my RT’s in stock form ever were.

For the modest investment and effort required for installation, the HVMP bar ends are a worthy addition for commuters, long distance travelers, riders with carpal tunnel syndrome and other related afflictions, and anyone else who desires less buzz in the bars. HVMP offers a wide selection of its American-made motorcycle bar end weights for various BMW and other brand models.

The post Hudson Valley Motor Parts Motorcycle Bar End Weights | Gear Review appeared first on Rider Magazine.

The popularity of adventure-touring motorcycles surged in the 2000s as more riders discovered their inherent versatility. So-called ADV bikes can not only eat up hundreds of miles each day but can also explore areas not frequented by most streetbikes. After a while, what many buyers of ADVs found was that there is potential danger to bouncing around the wilderness over rocks and logs, fording streams, and plowing through sand. One of those dangers is a punctured engine case many miles from help.   

The Harley-Davidson Pan America 1250, a fully featured and capable ADV powered by a 150-hp V-Twin, was launched in 2021. It was an immediate success, and soon Pan Americas were finding their way into some very challenging terrain in deserts, mountains, and canyons, including single-track trails more suitable for smaller displacement dual-sport motorcycles.  

Related: 2021 Harley-Davidson Pan America 1250 Special | First Ride Review

The stock Harley Pan Am is a very capable motorcycle. However, from the factory, the undercarriage is woefully exposed to damage from rocks, logs, and other hard objects that can be kicked up when riding off-road. Harley-Davidson offers a robust accessory skid plate to replace the thin aluminum protector in front of the battery.

The upgraded Harley skid plate is handsome, made from heavy duty aluminum and painted black. Using six bolts, it seemed to provide the level of underside armor needed for trails like Moab’s White Rim Trail and some of the Sierra Nevada trails that have sharp-edged rocks just waiting to end a ride should they puncture the nether regions of the engine.   

While the Harley skid plate provides protection – and the weight of it is held down low – it bolts right to the bottom of the engine rather than providing some sort of suspension to distribute the energy from a boulder or log hit.   

See all of Rider’s Parts & Accessories reviews here. 

Enter the Pan America Engine Guard from SW-Motech, which offers two key benefits over Harley-Davidson’s accessory skid plate. One is you can get it in either silver or black. Two, more functional and psychological support comes from the mounting system, which holds the engine guard off the bottom of the Pan Am’s 1250cc engine by about 0.5 inch with brackets that match up with the Pan Am’s original skid plate mounting holes. These mounts are able to provide a little more “give” should the engine guard be subjected to a heavy blow.  

The bottom of the SW-Motech engine guard is smooth and will help slide over logs and boulders. There are ample cooling holes to help with airflow around the bottom of the engine while also providing an escape path for mud and water that might collect during a water crossing.  

Installation took about 30 minutes. One mixed benefit to the SW-Motech engine guard is that it weighs less than the Harley skid plate. The SW-Motech engine guard weighs in at 7.4 lb, while the Harley skid plate weighs in at 10.7 lb. Although the overall weight reduction is good news, the Harley skid plate’s weight was at the very bottom of the engine and helped keep the center of gravity low. A few pounds doesn’t seem like much, but the change in weight distribution with the SW-Motech engine guard does shift the center of gravity up a little bit.  

The Pan America Engine Guard from SW-Motech retails for $446.95.  

The post Harley-Davidson Pan America Engine Guard from SW-Motech | Gear Review  appeared first on Rider Magazine.

Dr. Jekill & Mr. Hyde’s (J&H) novel exhaust system allows the rider to pick from three different sound modes on the fly. An illuminated, handlebar-mounted switch actuates a servo motor, which actuates a valve in the interior of the exhaust system to instantly adjust sound output to your preference.

In Dr. Jekill Mode, the valve is closed, diverting the exhaust gases around the valve and through perforations on side chambers of the exhaust, where they pass through patented single-strand fiber dampening material before being routed out. This is the quietest mode, most closely resembling the stock sound but with a much deeper tone.

A quick push of the button opens the valve halfway for Dynamic Mode, which adds a distinctive low-frequency bark. A final push of the button unleashes Mr. Hyde Mode, in which the valve opens fully and the rider is treated to the engine’s full guttural roar as exhaust gases pass through relatively unrestricted.

My BMW R 1250 GS exhaust system is governed by an ECU that plugs directly into the wiring harness, reading CANbus signals from the bike and allowing the exhaust valve to power on and off with the engine.

Related: 2021 BMW R 1250 GS | Road Test Review

Installation of the J&H exhaust is straightforward. The small servo motor is mounted to the frame above the header connection, and its waterproof control wires are routed along the inside face of the muffler, where an integrated clamp holds them securely. The wiring harness is plug and play. (J&H has a helpful installation video on YouTube.)

Once installed, the J&H is a handsome pipe. Its flawlessly finished Nomad Black body leads to a glossy hexagonal carbon fiber end cap, punctuated by a gorgeous machined-aluminum accent plate on the rear. The inlet cover is finished in matching glossy carbon fiber as well. The appearance is sleek, serious, and decidedly upmarket, drawing loads of attention from fellow GS riders.

See all of Rider‘s Parts & Accessories Reviews here.

Out on the road, the BMW’s personality can be instantly transformed from mild to wild depending on my mood, and I love exercising that expression! Experienced readers are wise enough to know the difference between an annoyingly loud exhaust and an improved exhaust tone that fits with the character of each motorcycle. This J&H pipe unleashed my bikes inner growl, adding a healthy dollop of welcome character to the machine.

But in this case, it’s not about volume. Using an AudioControl DMRTA calibrated decibel meter, placing the measurement device about 20 inches from the exhaust at a 45-degree angle per the SAE J2825 standard, I measured all three modes at idle: Dr. Jekill came in at 85.9 dB, Dynamic measured 88.1 dB, and Mr. Hyde rang up 93.1 dB. For reference, SAE J2825 recommends a 92 dBA limit at idle for motorcycles.

Dr. Jekill & Mr. Hyde exhausts are the best of both worlds, allowing you to be naughty or nice without ever being obnoxious. They’re made in the Netherlands and are fully compliant with European emission laws. Testing is currently in progress for the U.S. market, and the company hopes to have CARB and EPA approval by the end of 2023.

MSRP for the BMW R 1250 GS Exhaust from Dr. Jekill and Mr. Hyde is $1,695 for black and $1,640 for silver. Each pipe is covered by a four-year, unlimited-mile warranty.

The post BMW R 1250 GS Exhaust from Dr. Jekill and Mr. Hyde | Gear Review appeared first on Rider Magazine.

Rider’s former editor-in-chief, Mark Tuttle, gives us the lowdown on Touratech suspension service for the Touratech Extreme replacement rear shock for his BMW R 1200 GS.

One of the reasons I bought a lightly used 2007 BMW R 1200 GS was for its generous load capacity of 441 lb – a weight limit that’s pretty easy to hit when you’re two-up touring, even before breakfast.  

Although my wife and I were careful not to exceed that limit on our first long ride, it turned out that the bike’s stock rear shock simply wasn’t up to the task of carrying the loaded hard luggage, two of us in full riding gear, and 5 gallons of gas. Even with the spring preload maxed out, the back end sagged like an overloaded pickup truck, drastically slowing the GS’s normally responsive steering. The shock also bottomed out way too easily over big bumps. 

As soon as we got home, I gave the folks at Touratech USA a call. Back then as now, Touratech offers high-end Extreme front and rear shocks developed in Germany and built in the Netherlands by TracTive for 2007-2013 BMW oil-cooled R 1200 GS models. Although there’s more emphasis on the company’s replacement shocks with electronic suspension adjustment (ESA) these days, Touratech still sells and services TracTive Extreme components for many ADV bikes. These components are popular among riders who like to “geek out” on manually set suspension settings and get more in touch with their bike. 

Once I mounted up the Extreme shocks on my Beemer, I couldn’t have been more pleased. I wrote a full Touratech motorcycle suspension review for Rider in 2013, including a complete rundown of the shocks’ specs and features. 

Suffice it to say that the rear Extreme shock solved all my load carrying and handling problems and gave the bike a much better ride to boot. For that 2013 review, however, I wasn’t aware that Touratech specifies “regular” service intervals for its Extreme shocks. That makes sense; unlike the stock shock, as usual a poor compromise between performance and longevity, better performance means using parts that may wear. For comparison, rock-hard stock tires (a.k.a. rim protectors) versus premium replacement rubber with good grip but less longevity come to mind. 

Touratech says that whether it’s time for shock service at 10,000 miles or 30,000 miles really depends upon how hard the shock is used and how concerned the owner may be about preventing problems on a long remote ride. Over time, shock oil breaks down and gets contaminated, seals wear, and nitrogen pressure decreases, all leading to reduced performance and longevity issues, and you don’t want to damage something like the shock shaft, for example, by waiting too long. If you’re the type who’d rather not make the call, Touratech recommends two years or 20,000 miles on its Suspension Service Center website. 

In my case, the first interval turned out to be almost exactly 10,000 miles when I noticed that the lower shock seal was weeping oil – the first stage in the “weeping, seeping, leaking” progression from bad to worse. An hour later, I had the shock boxed up and ready to ship to Touratech in Seattle. Once service is complete, return shipping is included in the $150 fee ($200 for ESA shocks). In my case, it was Touratech’s slower season, so the turnaround time was only about two weeks, but it can take up to five at busier times. 

For this conventional shock service, Nick at Touratech disassembled, cleaned, and inspected the shock body and shaft, preload adjuster, damping piston, and shims. Replacing the damping piston ring is included. If any other worn or damaged parts need replacing (like the bump stop and seal head on my shock), Touratech only charges the cost of the parts – all labor is included. The remote reservoir did not need servicing, but oddly, the retainer ring for the lower clevis had come partially adrift, so Nick replaced the lower clevis, retainer ring, and circlip for good measure. The gang at Touratech had never seen this happen before; must have been that big jump… 

Once the shock was reassembled with fresh oil and nitrogen, Nick carefully boxed it up and shipped it back, and I was riding the BMW again within three weeks. Although I hadn’t noticed any degradation in performance before it was serviced, the rear suspension felt firm, supple, and controlled, as good as the first day I installed the Extreme shock back in 2013. 

Touratech also changes shock springs and services its electronic shocks and fork cartridges, all at a reasonable cost with free return shipping – all good reasons to consider putting its suspension products on your ADV bike in the first place. 

For more information, visit the Touratech website. 

The post Touratech Suspension Service | Gear Review appeared first on Rider Magazine.

After more than 17 years of riding successive generations of BMW RTs, I recently switched to riding a 2020 R 1250 GS. Even though my new-to-me GS is equipped with an oversized Puig Touring windshield, the amount of turbulence and wind noise at speed is significantly higher than it was on my former RTs. My last was a 2015 R 1200 RT equipped with the superb Werks Quiet Ride windshield, which enveloped the rider in a still pocket of calm air regardless of how fast the bike was moving. In fact, I’ve hosted several conference calls for work while traveling down the highway at extra-legal speeds, and nobody even knew I was in motion.

Related: 2021 BMW R 1250 GS | Road Test Review

In fairness, I never expected this level of protection from the GS, which is designed for adventure touring, not sport-touring like the RT. But for long highway trips and especially on cold days, I wanted more wind protection than what the stock bike offers. The hunt for solutions led me to Wunderlich Side Wind Deflectors, which fit 2017-18 R 1200 GS and 2019-23 R 1250 GS models, but not GS Adventure models.

Wunderlich’s deflectors are made of scratchproof, shatterproof 5mm acrylic plastic, and they’re available in clear or the dark tinted finish shown here. The kit includes two deflectors, a one-page installation sheet, and mounting hardware. Two brackets per side provide anchor points for the winglets, secured in place with standard M5 T25 Torx hardware running through a series of stabilizing collars and sleeves. There’s a bit of play for adjustability and fine tuning, if necessary.

As expected, it’s easiest if you install everything loosely at first, and then tighten down only once final adjustment is completed. Final installation as shown took less than an hour, working methodically. The Wunderlich winglets themselves, each measuring roughly 13 x 4.25 inches at the edges, are quite a bit larger than the stock deflectors on GS Adventure models, which measure roughly 10.5 x 3.5 inches.

Out on the road, the Wunderlich Side Wind Deflectors had a significant impact on the level of wind blast, overall turbulence, and noise experienced at highway speeds. The stock GS has moderate protection for the rider’s torso, but heavy airflow to the rider’s arms. I found that adjusting the windshield to a forward position (nearly vertical) in conjunction with the installed winglets notably diverted air around both my torso and my arms. This provided significant relief on long days gobbling up miles on the slab, which can get tiresome if the rider is being blown all over the place. For hot weather rides or if otherwise desired, the winglets can be quickly removed via 3x M5 T25 Torx bolts per side, allowing for maximum airflow.

Overall, the Wunderlich winglets are a worthy addition for BMW GS riders who partake in long trips at sustained high speeds, cold weather journeys, or otherwise desire a more composed operating environment. They’re priced at $289.95. (They’re also available for 2015-19 BMW S 1000 XR models for $271.95.) – Moshe K. Levy

For more information: See your dealer or visit WunderlichAmerica.com

The post Wunderlich Side Wind Deflectors for BMW GS | Gear Review appeared first on Rider Magazine.

Previous to hearing about the Zovii Alarmed Grip Lock, I was apparently naive when it came to motorcycle theft. At home, I always lock both my ignition and fork. What I didn’t know is that fork locks are relatively easy to break, albeit noisily. The noisy part is helpful if your bike is parked at your house, but what if you’re not home or you’ve taken it on a ride? Thieves can also lift a bike into a vehicle in a matter of seconds and take it elsewhere to disable security measures.

To address these issues, Aerostich offers the Zovii Alarmed Grip Lock, a waterproof nylon-construction lock with a 10mm carbide-reinforced hardened steel locking pin and a built-in 120dB anti-theft security alarm. For comparison, most emergency responder sirens range from 110-129db.

The lock is lightweight and compact. It weighs 8.7 ounces, about half an ounce heavier than my iPhone and case, and at 6 x 2.25 inches, it fits easily in the interior pockets on my leather jacket.

See all of Rider‘s Parts & Accessories reviews here.

To activate the alarm, clamp the lock around either grip and front lever on your bike and depress the lock button to arm it. No key is required to activate.

Unfortunately, the width of the stock grips and levers on my Harley Heritage Softail doesn’t allow the device to clamp entirely shut, so I tried it on a friend’s BMW R 1200 RT. The Zovii clicked on his grip and lever easily. However, when we took the bike off the centerstand and rolled it, I was surprised the alarm didn’t make a peep.

Here’s where a slight design flaw exists. The instructions say the unit beeps twice when you unlock it; however, we discovered after tinkering with it that two beeps means the alarm is disabled, even when it’s locked shut. Seems to me when you clamp the unit together and push the lock in, you also want to activate the alarm. However, you must make sure you hear a single beep (followed about five seconds later by a longer tone). If you clamp it together, push the lock in, and get two quick beeps, you must unlock it with the key and push it in again to get the single beep indicating that the alarm is activated. Slightly annoying, but I can see certain circumstances where this might be a good feature, primarily if you’re carrying the Zovii around and have to clamp it shut to do so.

Once we figured out the beeps, a slight jostling of the handlebar was enough to sound the warning tones. If we kept messing with it, we got the whammy 120 decibels, which is disarmed by unlocking the unit. The warning tones are nice in case you accidentally bump the bike or are concerned about how gingerly you have to unlock it when it’s armed.

So besides the minor inconvenience of the single vs. double beep – and the much bigger inconvenience of not fitting my bike – the Zovii is an inexpensive product (just $60) that’s loud enough to send a would-be thief scurrying back to the shadows.

The Zovii Alarmed Grip Lock is available at the Aerostich website.

The post Aerostich Zovii Alarmed Grip Lock | Gear Review appeared first on Rider Magazine.

Seeking relief from some of the strains of adventure bike riding, I thought I would test out one of the HeliBars Tour Performance Handlebar Risers. The riser positions the handlebar 2 inches higher and 2 inches closer to the rider, significantly altering the handlebar-seat-footpegs rider triangle.

See all of Rider‘s Parts & Accessories reviews here.

The handlebar position on many adventure bikes is well-placed for both sitting and standing while cruising backroads and maneuvering through technical off-road areas. Even on pavement, I find it helpful to stand up when riding through small towns to give my derriere a chance to get some blood back into it.

On my 2021 Harley-Davidson Pan America, with my 31-inch inseam, when standing on the pegs the stock handlebar position requires me to bend my knees slightly or stoop over a bit, which puts strain on my lower back. This riding position can become tiresome and uncomfortable after riding off-road over rough terrain. After an hour or so, my legs get pretty knackered.

Related: 2021 Harley-Davidson Pan America 1250 Special | First Ride Review

Enter the the HeliBars Tour Performance Handlebar Riser. Installation of the HeliBars riser is straightforward. Remove the stock handlebar, release some of the tie straps that secure brake lines and wires to the handlebar, reposition the lines behind the handlebar mount, and then install the HeliBars riser atop the stock handlebar mount. After that, simply re-install the stock handlebar on the new riser using bolts provided by HeliBars and torque them to appropriate spec. Nothing needs to be removed from the handlebar, and all stock lines are retained.

On a recent ride in the San Bernardino Mountains of Southern California, I put the riser to the test on the Santa Ana Divide Trail. It was fairly rutted with several rockslides and water crossings that required frequent standing. The HeliBars riser not only provided a more comfortable position but also helped with controlling the Pan Am and its significant heft. While I previously would have preferred to sit down for most of the ride, I found it equally comfortable to stand up for long stretches of deep sand and rutted two-track.

During long stints in the saddle, the new riser minimizes tension in my arms and shoulders, reducing fatigue and some of those post-ride aches and pains that are familiar to all of us. One downside to the new handlebar position is that it might block part of your view of the TFT dashboard depending on your height. For example, I now must lean forward a bit to see the clock since it’s located in the lower left corner of the screen.

HeliBars Tour Performance Handlebar Risers are machined from a single piece of 6061 T6 aluminum with nice craftsmanship, and their solid design reduces flex. They are functional, stylish, and manufactured on American soil in Cornish, Maine. The riser for the Harley Pan Am is priced at $199 – or $209 with the optional RAM ball mount. HeliBars also makes risers and replacement handlebars for a wide variety of other motorcycles. For more information, visit the HeliBars website.

The post HeliBars Tour Performance Handlebar Risers | Gear Review appeared first on Rider Magazine.

Adventure bike owners love to add “farkles” from companies such as National Cycle to their bikes. A farkle, as many of you know, is an accessory, often a fancy one, that a motorcycle owner is likely to brag about. Some say the word is a mashup of “function” and “sparkle,” but we’ve also heard it’s an acronym for Fancy Accessory, Really Kool, Likely Expensive. (When I Googled “farkle,” the top result was from Dictionary.com: a combination of fart and chuckle, an involuntary fart caused by laughter. Gotta love the internet.)

Best known for its windscreens and windshields, National Cycle also makes accessories for select motorcycle models. As part of its Extreme Adventure Gear (XAG) line, it makes accessories for the ADV-styled Honda CB500X, and we installed some XAG accessories on our 2022 test bike.

Related: 2019 Honda CB500X | First Ride Review

One of the most popular upgrades for adventure bikes is supplemental protection against rocks, road debris, and tip-overs. We started off with National Cycle’s XAG Polycarbonate Headlight Guard (P/N N5400, $84.95), which is made of tough 3.0mm polycarbonate reinforced with the company’s proprietary Quantum hardcoat – said to provide 10 times the strength and 30 times the scratch resistance as acrylic, a claim National Cycle backs up with a three-year warranty against breakage.

The guard is thermoformed for an exact fit over the 2019-2022 CB500X headlight, and its crystal-clear optics do not distort or reduce illumination. Installation is simple: Just clean the headlight, remove the adhesive backing on the marine-grade Velcro tabs, and press the guard onto the headlight lens.

Next, to add crash protection as well as a place to mount auxiliary lighting, we installed the XAG Adventure Side Guards (P/N P4200, $429.95), which are also available for the Yamaha Ténéré 700. Made of black powdercoated steel, they complement the CB500X’s styling, especially the Pearl Organic Green/Black color scheme on our 2022 model. The guards are also treated inside and out with an electrophoretic coating to eliminate rust and corrosion.

The installation instructions provide a list of basic tools needed as well as a QR code that links to a helpful video. Installation is straightforward and took about 30 minutes, with the only challenge being a little extra effort needed to line the guards up with the engine mount holes.

The left and right guards attach to the engine in two places, and they bolt together in the middle just below the headlight. Once installed, they provide solid, sturdy protection. A flat metal tab with an open bolt hole that’s welded to the lower part of each guard provides a good attachment point for auxiliary lights.

As Reg Kittrelle says in his Triumph Tiger 900 GT Low review in the upcoming February issue, an ADV is a “motorcycle that can comfortably take me to distant places carrying lots of stuff.” The Honda CB500X is comfortable, but in stock form, it doesn’t provide many options for carrying gear, so we installed the XAG Luggage Rack (P/N P9304, $184.95). Like the side guards, the luggage rack is made of black powdercoated steel.

Also like the guards, installation of the rack requires only basic hand tools, takes about 30 minutes, and is clearly demonstrated in the instructions and video. On a stock CB500X, installation requires removal/reinstallation of the passenger grab handles since the mounting brackets share the same bolt holes. On our test bike, the grab handles had already been removed when Honda’s accessory saddlebag mounts were installed. And be advised: National Cycle’s luggage rack is not compatible with Honda’s accessory saddlebags.

The rack is a solid, stylish, practical add-on. It measures 8.625 inches front to back and has a tapered width that narrows from 6.75 inches at the front to 5 inches at the rear. The rack’s slotted surface and two holes on either side provide anchor points for straps or bungee cords. It sits a bit higher than the passenger portion of the seat, but together they provide a platform up to 23 inches in length for carrying a drybag, duffel, or tailbag.

Related: Motorcycle Camping on a Honda CB500X and Husqvarna Norden 901

Although we didn’t request one for our test bike, National Cycle also makes the XAG Lowering Kit and Kickstand (P/N P4900, $119.95) for the CB500X. It includes a shorter sidestand and two aluminum suspension link arms that lower the seat height by about 1.5 inches (from 32.8 to 31.3 inches). Only basic tools are required, installation takes 30-45 minutes, and you’ll need a wheel chock and a hydraulic jack or lift. As with the other accessories, in addition to the step-by-step instructions with photos, there’s a helpful video.

We put as many miles as possible on our test bikes, so we’re always interested in accessories that improve comfort. We’ve tested National Cycle’s VStream windscreens on many different motorcycles over the years, and we’ve consistently been impressed with their ability to improve wind protection while also reducing turbulence and buffeting. With their patented “V” shape, VStream windscreens are made of 3.0mm Quantum-hardcoated polycarbonate – the same durable material used for the headlight guard (and with the same warranty against breakage).

The VStream windscreen comes in three sizes for the CB500X, as seen below.

The Low windscreen is 16.75 inches tall, just slightly taller than stock, and it’s available in dark or light tint for $121.95. We opted for the Mid windscreen ($133.95), which is 19.25 inches tall (more than 2.5 inches taller than stock), much wider than stock near the top, and available only in light tint. The Tall windscreen ($139.95) is 21.75 inches tall (more than 5 inches taller than stock), even wider near the top, and available only in clear.

Compared to stock, the Mid-size VStream pushes air higher up and around the rider. Airflow hits at helmet height, but there’s no buffeting. There’s also excellent visibility over the top of the windscreen, providing an unobstructed view of the road ahead.  

Unlike most farkles, National Cycle’s XAG accessories are practical and reasonably priced. If you’ve got a Honda CB500X, check ’em out by clicking on the linked product names above.

The post National Cycle Extreme Adventure Gear | Gear Review appeared first on Rider Magazine.

As I roll gently into my retirement years, I’ve taken to scouting used motorcycles on Craigslist to stock up my garage. I never know what will grab my attention and tickle my heart, and as I unearth hidden two-wheeled treasures, I’m usually delighted to inherit a rich assortment of accessories previous owners have lavished upon their bikes – now to become my next ride.

When acquiring used bikes, the one item that often requires my attention is the seat. Many riders work at lowering reach to the ground, but I’m 6 feet tall with a 31-inch inseam and grouchy hips. I like legroom. So when a newly acquired bike doesn’t fit me correctly, I head over to Legendary Best Motorcycle Seats in Ventura, California.

I’ve been using BMS for seat alterations for decades, beginning back in their Ojai days under Bill “Rocky” Mayer (BMS used to stand for Bill Mayer Saddles). Now, longtime stalwart Adrian Mercado handles the business, turning out the same quality work he’s crafted for all these years.

Read more of Rider‘s gear reviews

The personal fitting service at BMS is terrific. If you can devote a half day or so on site, Mercado and his crew will craft a custom-made seat built to your liking and personal fit while you wait. BMS also appears at rallies and other riding events across the country to provide custom services, or you can also send in your seat with your necessary personal dimensions for mail-order service.

Mercado listens to your requests, then makes suggestions based on his decades of seat-building experience. He’ll give you what you want, but I’ve learned to follow his advice, typically after some give-and-take regarding comfort versus aesthetics. The decision often comes down to a simple question: Do you want the bike to “look right,” or do you want the seat to coddle your rear end over a full day’s ride? Personally, I tend to lean toward the comfort side, but you can have it your way, exactly so.

Custom-built BMS seats absolutely transformed my new-to-me 2015 Ducati Multistrada 1200 S and 2017 KTM 690 Duke. Due to an extra-low seat at purchase, I found the Multi virtually unrideable, while the 690’s aftermarket rearsets shortened the seat/peg relationship and made things too cramped. Mercado fixed all of that, making both bikes more enjoyable – and “all mine” in the process. Nice. Problems solved.

Pricing begins at $595 to build a solo seat, pretty much in keeping with other custom seat options.

For more information, visit the Legendary BMS website.

The post Legendary Best Motorcycle Seats | Gear Review appeared first on Rider Magazine.